Why Carbon Hardtops Differ in Weight: Lotus Elise and Exige
A factory hardtop on a Lotus is not a light part. Both Aerie Performance hardtops listed at CarGym use the same figure for the factory OEM roof: 11 kg. On an Elise or Exige, that is a lot of mass sitting high on the car. The useful question is not whether a carbon replacement is lighter — it should be — but how much lighter, and what construction you are actually buying.
CarGym lists two Aerie Performance hardtops for the Lotus Elise S2 / S3 and Exige. They are not the same part.
The Aerie Performance Lotus Elise S2 / S3 & Exige Carbon Fiber Hardtop is described as fully carbon fibre, with a UV protective lacquer to prevent fading. The listing gives its weight as 6.5 kg, compared with the 11 kg OEM roof — 4.5 kg less. The shape is described as the same as the original, and the hardtop includes all brackets and seals for installation.
The Aerie Performance Lotus Elise S2 / S3 & Exige V Weave Carbon Fibre Double Side Hardtop is specified differently. It is a motorsports-grade, double-side herringbone V weave carbon fiber hardtop, made from pre-preg carbon fiber and autoclave-cured composites. The listing gives its weight as 4.3 kg — 7 kg lighter than the same 11 kg factory hardtop.
Those two numbers matter because “carbon fiber hardtop” is not a single specification. One of these roofs is 2.2 kg lighter than the other, and the lighter listing is also the one that describes pre-preg material and autoclave curing.
What pre-preg and autoclave curing are
In a pre-preg part, the carbon fabric is already impregnated with a measured amount of resin before it is laid into the mould. The laminate is then typically cured under heat and pressure in an autoclave. The point of that process is control: less leftover resin than a wet-laid part, and a more consistent, compact laminate. The V-weave listing also describes those pre-preg materials as high-impact and shatter-resistant, and it warns that some parts with “half-carbon” features can end up heavier than the OEM piece they replace. Weight is not guaranteed just because a roof is labeled carbon.
What the herringbone V-weave and “double-side” are telling you
The V-weave hardtop uses a herringbone V weave that the product page says resembles the OEM carbon fiber hardtop. That pattern is visible on the fitted roof in the photos, and it is not the same as a standard twill. The listing calls this a double-side hardtop, and the official underside photos show the carbon weave on the inner face as well as the exterior.
The V-weave hardtop is designed to full OEM specifications so the original underside reinforcement panels can be re-fitted. Those panels are not included as new parts; they come off the original hardtop. The listing does include a windows rubber seal kit for a plug-and-play install. In the fitted interior photo, those underside panels are already in place.
The 6.5 kg hardtop takes a different approach to hardware. That listing includes all brackets and seals, and it is described as directly compatible for installation to motorsports safety standards.
What to confirm before you order
Fitment is close on both listings, but the wording is not identical. The 6.5 kg hardtop is listed as compatible with the S2/S3 Lotus Elise and Lotus Exige (all models). The 4.3 kg V-weave hardtop is listed for the Lotus Exige, including Exige S2 and Exige V6, and the Lotus Elise S2 / S3. Confirm the exact chassis — Elise or Exige, and the generation — against the product page before ordering. Neither listing is written for other Lotus models.
Both hardtops are made to order and take 3–4 weeks to ship after order confirmation. Professional installation is recommended on both pages for the cleanest alignment and finish.
A short checklist, taken from the listings themselves:
- Confirm the car is a Lotus Elise S2 / S3 or a listed Exige (the V-weave page specifies Exige S2 and Exige V6).
- Decide which construction you want: the 6.5 kg fully carbon fibre hardtop with UV protective lacquer, or the 4.3 kg pre-preg, autoclave-cured, double-side herringbone V-weave hardtop.
- Check what is included. The 6.5 kg hardtop includes all brackets and seals. The V-weave hardtop includes a windows rubber seal kit, and requires the original underside reinforcement panels to be re-fitted; those panels are not supplied as new parts.
- Plan for a made-to-order lead time of 3–4 weeks after confirmation, and for professional installation.
The two parts discussed above are the Aerie Performance Lotus Elise S2 / S3 & Exige Carbon Fiber Hardtop and the Aerie Performance Lotus Elise S2 / S3 & Exige V Weave Carbon Fibre Double Side Hardtop.